TROUBLESHOOTING / WELD LINES

Control weld lines where flow fronts meet and air is trapped.

A weld line is a visible or structural seam created when separate melt fronts join. It can affect appearance, strength, sealing and leak performance, especially in glass-filled or high-viscosity resins.

ABERY engineering note
Updated November 20, 2026

A weld line is not only a cosmetic defect. The structural and sealing requirement determines whether the correct response is process, gate, venting or part-design change.

QUICK ANSWER

Map where the flow fronts meet, inspect venting and gate location, review fill and packing, and determine whether the weld is cosmetic, structural or sealing-critical. Process changes can reduce visibility, but a durable fix often requires flow, venting or design correction.

1. Classify the weld line.

An appearance-only weld line may be acceptable if it matches the approved sample. A weld line across a seal, pressure boundary or structural feature may be unacceptable even when it is barely visible.

Record the location, direction, cavity, lighting, leak or strength test result and whether the line changes with fill speed or temperature. This determines the acceptance criterion.

  • Cosmetic surface requirement.
  • Structural or impact requirement.
  • Sealing or leak requirement.
  • Assembly or fit requirement.
  • Gate and flow-front location.
  • Venting condition at the merge point.

2. Review gate, flow and venting.

Gate location determines where flow fronts meet. Changes to gate position, runner balance or part geometry can move the weld line away from a critical surface.

Air trapped at the merge point can create a weak or discolored weld. Check venting, vent depth, vent cleanliness and the ability of air to escape before the cavity fills.

Gate positionMove the merge zone away from a cosmetic or sealing area.
Fill patternReview injection-speed profile and balanced flow.
VentingVerify vent location, depth, cleanliness and blockage.
Melt temperatureUse the resin supplier’s range; excessive heat can degrade color.
Mold temperatureImprove local flow-front fusion where appropriate.
MaterialGlass-filled resins can create anisotropic strength at the weld.

Check the function first.

Do not approve a structurally critical weld line only because it looks better.

Review flow analysis

3. Validate with the correct test.

For appearance, use the same lighting and sample boundary as the customer. For function, use the relevant leak, impact or assembly test. A photo is not a substitute for a strength or sealing test.

Keep samples from each cavity and process variant. Compare the weld location and test result under the same measurement condition.

  • Keep good and bad samples by cavity.
  • Record gate, fill time, melt/mold temperatures and packing.
  • Check the weld before and after any tool or process change.
  • Repeat the validation across a stable production run.
  • Document the approved appearance and functional boundary.

4. When to change the tool.

If the weld line cannot be moved away from the critical area or the required strength cannot be reached, a gate or part-design change may be necessary. The cost of changing the tool should be compared with the cost of inspection, scrap and field risk.

Do not use a cosmetic process tweak to hide a structural defect without engineering approval.

Send the whole picture.

Include the part, gate concept, flow analysis, material and failure mode.

Discuss a weld-line issue

Questions buyers ask before approving this scope.

Can weld lines be eliminated completely?
Many multi-gate or multi-flow parts will have a merge line. The goal is to control its location and appearance or ensure the required strength and sealing performance.
Are weld lines weaker than the surrounding material?
They can reduce strength, especially in glass-filled resins or with trapped air. The actual effect depends on material, merge angle, venting and process.
Does higher injection speed always improve a weld line?
No. It can change flow and temperature but may also create jetting, burn marks or trapped gas. Validate the result with the actual part and boundary.
Should a weld line be documented on the drawing?
Critical appearance or sealing areas should be identified. The approval sample and test method should define what is acceptable.

Need a project-specific answer?

Send the part, material, volume and stage. We will identify what can be confirmed before quotation or tooling.

Send the project

Keep the scope comparable.

The linked guides are written to support a project-specific supplier and tooling review.

PROJECT INTAKE / FLOW REVIEW

Move the weld line before it becomes a launch risk.

Share the part, gate concept, resin and functional requirement. We can review the flow and validation questions before tooling approval.

Part geometryGate conceptResinFlow analysisLeak/strength testCosmetic standard

Tell us where the project is now.

Send the files and context you have. Missing information can be confirmed during review.

A-MOLD Project Inquiry

Business inquiries only. For large files, include a secure Google Drive, Dropbox, OneDrive or WeTransfer link, or email tonney@a-mold.com after submitting.