DESIGN GUIDE / PARTING LINE
The parting line is a cosmetic, sealing and tooling decision.
The parting line determines where the mold opens, how the part releases, where flash can form and which surfaces carry a witness mark. Moving it can solve one problem while creating another in appearance, assembly or maintenance.
ABERY engineering note
Updated November 20, 2026
A parting line that is acceptable on a hidden surface may fail on a seal or A surface. Review it with the product function, not only the mold layout.
QUICK ANSWER
Review the part geometry, pull direction, undercuts, cosmetic surfaces, sealing faces, draft, venting and tool structure. Define the parting-line location and shutoff condition, then validate flash, witness marks, dimensions and mold release at T1. A parting-line change after steel requires a clear impact review.
1. Identify what the line touches.
A parting line can cross an appearance surface, a sealing face, an assembly edge or a hidden structural area. The same line location can be acceptable in one region and unacceptable in another.
Mark the cosmetic and functional surfaces on the drawing before the mold layout is approved. If a line must cross a visible area, define its allowed width, color, flash and finishing condition.
| Appearance | Witness line, gloss and color boundary. |
|---|---|
| Seal | Flatness, surface and leak risk. |
| Assembly | Gap, flush and mating condition. |
| Release | Draft and ejection path. |
| Tool | Slides, lifters and shutoffs. |
| Maintenance | Wear and flash control. |
2. Set the pull direction before the parting line.
The mold opening direction determines which features can be released without side actions. The parting line follows that decision, not the other way around.
Undercuts, textured walls and cosmetic edges may require a side action or a different line location. Compare the visible and functional impact before adding tool complexity.
- Primary pull direction.
- Undercuts and side actions.
- Draft and texture.
- Cosmetic surface boundary.
- Seal and assembly faces.
- Ejection and maintenance access.
3. Design the shutoff and venting.
The shutoff controls flash and wear at the parting line. It should be strong enough for the injection pressure and accessible for maintenance.
Venting should allow air to escape without creating a visible witness line or a weak edge. Vent location and depth should be reviewed with the last-fill area.
| Shutoff | Land, clearance and wear. |
|---|---|
| Vent | Location, depth and cleaning. |
| Flash | Pressure, clamp and tool condition. |
| Draft | Release near the line. |
| Steel | Hardness and repair access. |
| Finish | Texture and polishing. |
4. Control the visible result.
A parting line may show as a raised edge, color difference, polishing mark or flash. The acceptable boundary should be defined with a physical sample or photo standard.
If the line is on a textured surface, the texture should be continued across the shutoff without creating a mismatch. If the line crosses a seal, the shutoff and flatness need a functional check.
- Allowed witness-line width.
- Flash and trimming boundary.
- Texture match.
- Polishing direction.
- Seal or assembly check.
- Retained boundary sample.
5. Validate before and after T1.
At T1, inspect the line under the agreed lighting and check flash, part release, dimensions and assembly. Run enough cycles to see whether the condition changes as the tool warms.
If the parting line moves, review the effect on undercuts, draft, venting and the approved sample. A tool change should be recorded and revalidated.
- Witness line and flash.
- Release and ejection.
- Dimensional and assembly result.
- Seal or leak check.
- Approved sample and drawing.
- Revalidation trigger.
Questions buyers ask before approving this scope.
Where should the parting line be?
Can a parting line be invisible?
Does the parting line affect mold cost?
How is a parting line inspected?
Need a project-specific answer?
Send the part, material, volume and stage. We will identify what can be confirmed before quotation or tooling.
Send the projectContinue the engineering review.
Keep the scope comparable.
The linked guides are written to support a project-specific supplier and tooling review.
PROJECT INTAKE / PARTING LINE
Send the cosmetic and sealing boundaries.
We will review pull direction, undercuts, witness lines, venting and tool maintenance before the mold layout is fixed.
Tell us where the project is now.
Send the files and context you have. Missing information can be confirmed during review.
Business inquiries only. For large files, include a secure Google Drive, Dropbox, OneDrive or WeTransfer link, or email tonney@a-mold.com after submitting.