TROUBLESHOOTING / EJECTION MARKS

Ejection marks are a force, contact and release problem.

An ejection mark can be a raised pin witness, a white stress mark, a scratch, a dent or a distorted area. The cause may be pin location, contact area, draft, shrinkage, cooling, surface finish or the handling step after release.

ABERY engineering note
Updated November 20, 2026

Do not polish every mark away. A change to the contact surface can alter release and create a different defect.

QUICK ANSWER

Photograph the mark and identify the exact ejector, lifter or handling contact. Review draft, shrinkage, ejection force, pin area, surface finish, cooling and part support. Correct the dominant cause, then check appearance, dimensions and repeated release at T1.

1. Identify the mark and contact point.

A pin mark may be a shiny spot, a small raised ring, a white stress area or a gouge. The location should be matched to the ejector layout and the part surface.

Check whether the mark appears on the first shot or after a run, and whether it changes with ejection pressure or mold temperature.

Raised witnessPin contact or tool damage.
White stressPoint load or excessive force.
ScratchDrag, rough surface or handling.
DentPart impact or support issue.
DistortionUnbalanced ejection or insufficient draft.
Repeat markWear or a fixed tool condition.

2. Improve release before increasing force.

Insufficient draft, shrink grip, rough finish or a deep texture can make release difficult. More ejection force can worsen marks and damage the part.

Review the core surface, draft and cooling first. A small tool change may produce a better result than a large process change.

  • Draft and texture.
  • Core polish and drag.
  • Shrinkage and cooling.
  • Ejection contact area.
  • Pin or sleeve alignment.
  • Part support.

3. Redesign the ejection contact.

Larger pads, sleeves, stripper plates or additional pins can distribute force. The contact area should be strong and outside the cosmetic or sealing surface.

If a pin must contact a visible area, define the allowed witness and verify it with a boundary sample.

Pin sizeContact pressure and visibility.
PadForce distribution and witness.
SleeveAround a boss or cylindrical feature.
StripperLarge-area release and edge risk.
LifterCombined release and motion.
AirSurface and sealing condition.

4. Control the process window.

Ejection timing, mold temperature and hold pressure affect how tightly the part grips the core. A change made for cycle or sink may change the ejection force.

Record the ejection condition and check the first, middle and last parts from a stabilized run.

  • Cooling time and mold temperature.
  • Packing and part shrinkage.
  • Ejection timing and pressure.
  • Cycle stability.
  • Material lot.
  • Cavity identification.

5. Protect the part after ejection.

The mark may occur after the part leaves the mold if it falls, rubs a chute or is packed under pressure. Observe the full removal path.

Define the handling method and packaging for cosmetic parts. A small process correction may be useless if the part is damaged downstream.

  • Robot or manual removal.
  • Chute and bin design.
  • Tray orientation.
  • Gloves and surface protection.
  • Packaging contact.
  • Final appearance check.

Questions buyers ask before approving this scope.

Why do ejector pins leave white marks?
The pin may be applying too much point force, the part may be gripping the core or the material may be stressed. Draft, contact area, ejection and cooling should be reviewed.
Can polishing remove an ejection mark?
Polishing may change the tool surface and release, but it does not fix an ejector layout or process problem. The cause should be identified first.
What is a normal ejector-pin witness?
The acceptable witness depends on the cosmetic and functional surface. It should be defined with a sample and checked under the agreed lighting.
How can handling marks be separated from mold marks?
Observe the part immediately after ejection and again after removal, handling and packaging. Mark the exact point where the defect appears.

Need a project-specific answer?

Send the part, material, volume and stage. We will identify what can be confirmed before quotation or tooling.

Send the project

Keep the scope comparable.

The linked guides are written to support a project-specific supplier and tooling review.

PROJECT INTAKE / EJECTION MARK

Send the mark location and removal path.

We will help separate tool contact, release, process and handling causes before changing the surface.

Defect photosEjector layoutPart materialProcess sheetHandling methodCosmetic standard

Tell us where the project is now.

Send the files and context you have. Missing information can be confirmed during review.

A-MOLD Project Inquiry

Business inquiries only. For large files, include a secure Google Drive, Dropbox, OneDrive or WeTransfer link, or email tonney@a-mold.com after submitting.