MATERIALS / TPE & TPU OVERMOLDING
Soft-touch overmolding starts with adhesion and shutoff control.
TPE and TPU can add grip, sealing, damping or a soft-touch surface to a rigid substrate, but the material pair must be designed for adhesion, processing temperature, shrinkage and the mechanical load. The mold and the process have to validate the bond together.
ABERY engineering note
Updated November 20, 2026
Hardness alone does not define a TPE or TPU grade. Ask for the exact grade, adhesion system, processing window and substrate condition.
QUICK ANSWER
Confirm the substrate and overmold grade, chemical or mechanical bond, hardness, color, surface requirement and end-use environment. Then define substrate geometry, shutoffs, gate location, overmold thickness, drying, first-shot condition and T1 bond testing before approving the tool.
1. Select the material pair before choosing the tool.
TPE and TPU are broad families, not a single material. The grade may bond chemically to a specific substrate, rely on mechanical interlocking, or need surface treatment or a primer. A data sheet may list hardness and elongation while saying little about adhesion to the actual resin and geometry.
Review the substrate grade, overmold thickness, flexibility, temperature exposure, chemical contact, color, surface texture and expected service life. If the part is intended for repeated flexing, impact or sealing, include that in the material and validation requirements.
| Substrate | Exact resin, grade, shrinkage and surface condition. |
|---|---|
| Overmold | TPE or TPU family, hardness, color and adhesion system. |
| Bond | Chemical affinity, mechanical locking or approved surface preparation. |
| Environment | Temperature, UV, chemicals, cleaning and flexing. |
| Appearance | Texture, gloss, gate mark and color boundary. |
| Validation | Peel, pull, flex, seal or functional test agreed in advance. |
2. Design the first shot for a reliable second shot.
The substrate needs the correct wall thickness, shrinkage allowance, mechanical retention and surface condition. Sharp edges, weak bosses and abrupt thickness changes can create sink, warpage or bond failure. The overmold needs uniform cavity pressure and a controlled shutoff so the soft material stays where it is intended.
Review where the two materials meet. A shutoff that creates flash, traps gas or damages the substrate may look acceptable at T1 and fail in production. Consider wear on shutoffs, ejection marks and how the part will be handled between shots.
Treat the interface as a feature.
The bond line and shutoff should be dimensioned, inspected and included in the sample approval record.
Review 2K overmolding3. Control drying, heat and residence time.
TPU grades can be moisture-sensitive, while TPE formulations differ widely. Confirm the exact drying and processing recommendation with the material supplier. The overmold also has to be processed at a temperature that supports adhesion without distorting or degrading the substrate.
Review melt temperature, injection speed, packing, cooling and cycle time together. Higher temperature may improve bond but can increase flash, substrate movement or degradation. A lower temperature may protect the substrate but produce a weak or cosmetic bond.
- Confirm dryer type, temperature and residence time.
- Check compatibility with the substrate and insert materials.
- Record actual melt and mold temperatures.
- Review injection speed, pressure transfer and packing.
- Check cooling and part release without stretching the soft material.
- Keep startup and shutdown purge procedures documented.
4. Validate the bond and the production window.
The first sample should be checked for appearance, dimensions, bond integrity and function. A pull or peel test, if required, needs a defined specimen, rate, direction, failure mode and acceptance criterion. A visual check alone does not prove the interface will survive handling and use.
Run the qualification across cavities and across a representative run. Then repeat after a color change, material lot change, short shutdown or planned maintenance if those conditions can affect adhesion. Record the process settings that produced the accepted samples.
- Appearance and color boundary.
- Substrate and overmold dimensions.
- Bond or peel result, including failure mode.
- Functional checks for grip, seal or flex.
- Cavity and shot traceability.
- Process window and revalidation triggers.
5. What the toolmaker needs for a useful review.
Send the 3D part and 2D drawing, exact substrate and overmold grades, color and texture requirements, annual volume, press size, bond requirement and any cleaning or environmental exposure. Identify which surfaces are cosmetic and which are functional.
If the part already exists, include the current tool condition, process sheet, defect photos and bond test results. This helps separate a material problem from a shutoff, gate or machine issue.
Do not assume a bond.
If adhesion is critical, specify how it will be measured and who will approve the result.
Compare process optionsQuestions buyers ask before approving this scope.
Can TPE overmold onto any plastic?
What does Shore hardness tell me?
Can a primer be used?
How should the bond be inspected?
Need a project-specific answer?
Send the part, material, volume and stage. We will identify what can be confirmed before quotation or tooling.
Send the projectContinue the engineering review.
Keep the scope comparable.
The linked guides are written to support a project-specific supplier and tooling review.
PROJECT INTAKE / TPE-TPU REVIEW
Define the bond before the tool is cut.
Send the substrate, overmold grade, part function and test requirement. We will identify the tool and process questions that need to be closed.
Tell us where the project is now.
Send the files and context you have. Missing information can be confirmed during review.
Business inquiries only. For large files, include a secure Google Drive, Dropbox, OneDrive or WeTransfer link, or email tonney@a-mold.com after submitting.