DESIGN GUIDE / GATE LOCATION
Gate location is a compromise between fill, appearance and control.
The gate determines how resin enters the cavity, where pressure is transferred, how fibers orient and where weld lines appear. A gate that fills the part may still create a cosmetic, warpage or degating problem that costs more than the original tool.
ABERY engineering note
Updated November 20, 2026
There is no universal best gate. The decision depends on the part geometry, resin, filling pattern, packing path, cosmetic surface and measurement requirement.
QUICK ANSWER
Review wall and flow length, resin behavior, weld-line location, fiber orientation, cosmetic boundary, packing, cooling and degating before selecting the gate. Compare gate type and location with DFM or Moldflow where suitable, then confirm the gate in T1 and link it to the approved sample and process.
1. Define what the gate must achieve.
A gate must fill the cavity, transfer pressure to the packing areas and allow a repeatable cycle. It also creates a witness mark, a flow pattern and a weld line. Those effects belong to the design decision, not the finishing discussion.
Start with the part function and the manufacturing requirement. A hidden gate may be preferred for appearance but can create a difficult flow path or pressure loss. A central gate may fill evenly but conflict with an assembly feature.
| Fill | Flow length, pressure and short-shot risk. |
|---|---|
| Pack | Pressure path and gate freeze. |
| Appearance | Gate mark, flow marks and weld lines. |
| Material | Shear, fiber orientation and degradation. |
| Tool | Runner, ejection and maintenance access. |
| Finishing | Degating and handling. |
2. Compare gate types by the actual risk.
Edge, tunnel, direct, hot-tip, valve and fan gates create different shear, packing and cosmetic conditions. A hot runner may reduce runner waste or support sequencing, but it adds controller, heat-history and maintenance scope.
The comparison should include the part and the production plan. A gate that is easy to machine may not be easy to maintain or reproduce across cavities.
- Edge or direct gate.
- Tunnel or submarine gate.
- Hot tip or valve gate.
- Fan or film gate.
- Gate vestige and removal.
- Runner and controller maintenance.
3. Place the gate against flow and assembly.
Gate location can create a weld line in a high-stress area, trap air at the last-fill point or make a visible flow mark on the A surface. It can also make a boss or thin section difficult to pack.
Review the flow simulation or short-shot pattern with the actual feed system. If the gate must move, evaluate the effect on the whole part rather than only the gate mark.
| Weld line | Place away from strength or cosmetic critical area. |
|---|---|
| Air trap | Provide venting at the last-fill point. |
| Thin section | Avoid forcing the flow through a restrictive feature. |
| Boss/rib | Check local packing and sink risk. |
| Fiber | Review orientation and warpage. |
| Assembly | Keep gate and vestige away from sealing surfaces. |
4. Check packing and gate freeze.
The gate must remain open long enough to transfer packing pressure, but it cannot leave an oversized vestige or create excessive cycle time. The resin, gate thickness, mold temperature and part section determine the condition.
If the gate freezes early, the part may sink or warp even when the pressure setting is high. If it stays open too long, cycle time and degating effort increase.
- Gate thickness and land length.
- Gate freeze time.
- Packing pressure and hold time.
- Mold and melt temperature.
- Part section and flow path.
- Cycle and degating method.
5. Prove the gate in T1.
Inspect the first and last parts, all cavities and the last-fill area. Record the short-shot pattern, gate condition, vestige, weld line and process settings.
A gate change can affect dimensions, appearance, fiber orientation and cycle. If the gate is moved or resized, update the mold record and define the sample and process revalidation requirement.
- Short-shot and fill balance.
- Gate freeze and packing.
- Weld-line and air-trap location.
- Gate mark and degating.
- Dimensional and appearance result.
- Approved process window.
Questions buyers ask before approving this scope.
Where should an injection molding gate be located?
Does a hot runner solve gate-location problems?
Can gate location cause warpage?
What should a T1 report show about the gate?
Need a project-specific answer?
Send the part, material, volume and stage. We will identify what can be confirmed before quotation or tooling.
Send the projectContinue the engineering review.
Keep the scope comparable.
The linked guides are written to support a project-specific supplier and tooling review.
PROJECT INTAKE / GATE REVIEW
Send the part and the cosmetic boundary.
We will review gate options against fill, packing, appearance, fiber orientation and tool maintenance.
Tell us where the project is now.
Send the files and context you have. Missing information can be confirmed during review.
Business inquiries only. For large files, include a secure Google Drive, Dropbox, OneDrive or WeTransfer link, or email tonney@a-mold.com after submitting.