RESOURCE / TOLERANCE PLANNING

Specify injection molding tolerances by feature, not by habit.

A single global tolerance rarely tells a mold maker what matters. Functional features, assembly interfaces, cosmetic surfaces and measurement methods need different controls—and different amounts of tooling and inspection effort.

ABERY engineering note
Updated November 20, 2026

The drawing should distinguish general tolerances from critical-to-quality features. If every dimension is treated as critical, the quotation and inspection plan become unclear.

QUICK ANSWER

Start with general tolerances, then identify the few dimensions that control fit, function, assembly or appearance. For each critical feature, state the nominal value, tolerance, datum scheme, measurement method and whether the tolerance applies before or after plating, coating or assembly.

1. Why a single tolerance is not enough.

Injection-molded parts vary because of tool dimensions, shrinkage, resin, orientation, cooling, packing, machine repeatability and measurement method. A tolerance that is easy to state on a drawing may be difficult or expensive to hold consistently on a production tool.

The useful question is not “what is the tightest tolerance possible?” It is “which dimensions affect the buyer’s function, and how will both parties prove that they are acceptable?” A 120 mm housing may have a general tolerance for non-functional surfaces and tighter controls for a connector, seal or snap-fit interface.

A feature-based tolerance hierarchy

General geometrySurfaces and dimensions that do not affect fit, function, assembly or appearance. Use the drawing general tolerance unless a critical feature says otherwise.
Assembly interfaceA controlled feature where cumulative stack-up affects the customer’s assembly. Define datums, mating condition and inspection method.
Seal or wear surfaceA feature where flatness, roundness, surface finish or local dimension affects function. Measurement should reflect the actual use condition.
Cosmetic boundaryAppearance requirements such as texture, gloss, color and visible defects. These are often visual standards rather than dimensional tolerances.

Do not hide critical features.

If a supplier cannot identify which dimensions drive function and inspection, the RFQ is incomplete.

Open the RFQ checklist

2. Resin and process choices change the achievable result.

Glass-filled resins may show direction-dependent shrinkage and warpage. Transparent resins may reveal flow marks, stress or gate evidence that a dark textured material would hide. Flame-retardant grades may have a narrower process window.

Tolerance planning should therefore include the exact resin grade, filler percentage, color and additive package. If the resin is not final, the supplier should state what assumptions were used in the quotation and which ones must be rechecked before steel is cut.

  • Drying and moisture condition can affect dimensional stability and appearance.
  • Gate location and fiber orientation can change local shrinkage.
  • Cooling and packing influence warpage and post-molding movement.
  • Ejection and part handling can create distortion or measurement error.
  • Inspection temperature and settling time should be agreed for critical dimensions.

3. A practical drawing and measurement package.

A production-ready drawing should make the acceptance logic understandable without a meeting. It should show the revision, material, general tolerance, critical dimensions, datums, critical-to-quality markings and any special inspection requirement.

For complicated parts, attach a measurement plan or a marked inspection diagram. A phone photo of a sample is useful context, but it is not a substitute for a controlled drawing.

What the drawing should state

  • General tolerance and the standard used.
  • Critical dimensions and their individual tolerances.
  • Datum structure and feature-control requirements.
  • Appearance, texture, gloss and color standard.
  • Measurement timing, fixture and inspection method where relevant.
  • Whether the requirement applies to T1, approved samples or production parts.

4. How to negotiate a tolerance without guessing.

If a feature is difficult to hold, review the function with the mold maker before changing the number. There may be a better datum, a more stable gate location, a different feature design or a measurement method that reflects the assembly condition.

When a tolerance is genuinely critical, price the inspection and process capability rather than assuming that every tool will hold it. A supplier should explain the machine, fixture, CMM or gauge needed and how variation will be monitored in production.

A tolerance is a control plan.

The number, datum and measurement method should travel together from drawing to T1 and production.

Review T1 validation

Questions buyers ask before approving this scope.

What is a typical injection molding tolerance?
There is no single universal figure. General tolerances are often stated on the drawing, while critical dimensions need feature-specific requirements based on resin, geometry, tool design, process capability and measurement method.
Should every dimension be marked critical?
No. Marking every dimension as critical makes the quotation, inspection plan and corrective-action discussion less useful. Identify the few features that control fit, function, assembly or appearance.
Does a CNC-machined mold automatically hold a tight tolerance?
No. Mold machining accuracy is only one part of the system. Resin shrinkage, cooling, packing, ejection, machine repeatability and measurement uncertainty also affect the molded part.
What should I send with the drawing?
Send the 3D CAD, 2D drawing, exact resin grade, volume, appearance standard, critical-to-quality features and any known measurement method or fixture.

Need a project-specific answer?

Send the part, material, volume and stage. We will identify what can be confirmed before quotation or tooling.

Send the project

Keep the scope comparable.

The linked guides are written to support a project-specific supplier and tooling review.

PROJECT INTAKE / TOLERANCE REVIEW

Make the critical dimensions reviewable.

Send the drawing, 3D model, resin and assembly requirement. We will identify the features that need a measurement and tooling plan.

3D / 2D filesResin gradeCritical dimensionsAssembly requirementTarget volumeInspection method

Tell us where the project is now.

Send the files and context you have. Missing information can be confirmed during review.

A-MOLD Project Inquiry

Business inquiries only. For large files, include a secure Google Drive, Dropbox, OneDrive or WeTransfer link, or email tonney@a-mold.com after submitting.