METROLOGY / CMM INSPECTION
A CMM result is only useful when the measurement plan is defined.
Coordinate measuring machines can measure mold components, electrodes, inserts and molded parts with high repeatability, but the number does not explain itself. Datums, alignment, probe access, temperature, fixture condition and the inspection program determine whether the result answers the drawing.
ABERY engineering note
Updated November 20, 2026
A report should identify the part revision, program, datum scheme, fixture, probe system and measurement environment—not only a column of pass/fail values.
QUICK ANSWER
Agree the drawing revision, critical characteristics, datum scheme and acceptance method before inspection. Confirm probe access, fixturing, part condition and program validation. Review the raw result, measurement uncertainty and any out-of-tolerance feature with the design intent, not only the nominal.
1. Separate mold inspection from part inspection.
A mold component and a molded part are different measurement objects. Mold steel may be checked for geometry, fits, insert pockets, water lines, guide-pin positions and assembly clearances. A molded sample may be checked for drawing dimensions, free-state shape, assembly condition and critical features.
Both can use a CMM, but they need different fixtures and programs. Ask what is being measured and why. A beautiful CMM report for a mold plate does not prove that the molded part meets the part drawing.
| Mold component | Plate geometry, pockets, fits, guide and ejector positions. |
|---|---|
| Electrode | Shape and position before EDM, with the correct program. |
| Insert | Critical dimensions, shutoffs and assembly fit. |
| Molded part | Drawing dimensions in a defined free or restrained state. |
| Fixture | Repeatable location and clamping condition. |
| Program | Part revision, alignment and probe qualification. |
2. Define the datum and inspection condition.
The drawing should identify the primary, secondary and tertiary datums. If the part is flexible or has an assembly condition, state whether it is measured free, restrained or assembled. A different datum or clamping force can change the reported result.
For mold components, define the setup orientation and the relationship between the machined feature and the tool datum. For molded parts, define gate, cavity, cooling time and settling time if the material can move after ejection.
Agree the report before T1.
The supplier and buyer should know which characteristics will be reported and how an out-of-tolerance result will be handled.
Review tolerance strategy3. Check probe access and fixture risk.
Small ribs, deep pockets, undercuts and soft materials may limit probe access or distort during contact measurement. The inspection plan should identify features that cannot be measured directly and the alternative method. Optical, tactile, gauge or functional checks may be more appropriate for some characteristics.
A fixture can hide a problem by forcing a flexible part into shape. Review how the part is supported, how it is clamped and whether the reported result represents the condition the customer will assemble.
- Probe length and access to critical features.
- Fixture repeatability and clamping force.
- Part cleanliness and temperature.
- Program revision and probe qualification.
- Feature construction and alignment method.
- Alternative gauge or functional check where direct CMM is unsuitable.
4. Read the result with the drawing intent.
A pass/fail table is not enough for a technical review. Look at the measured value, tolerance, deviation direction and pattern across cavities. A small dimensional shift may be stable and acceptable for function, while a visually small feature error may affect assembly or sealing.
If a result is out of tolerance, ask for the raw report, the datum setup and the sample condition. Repeat the measurement before changing steel if the cause could be fixturing, program, temperature or part movement.
- Nominal, tolerance and measured value.
- Deviation and direction.
- Cavity and sample identification.
- Repeatability or recheck result.
- Measurement uncertainty where relevant.
- Corrective action and revalidation.
5. Use CMM as one part of acceptance.
CMM inspection supports dimensional acceptance but does not replace material certification, appearance review, fit, function, mold operation, water-circuit checks or safety verification. A complete acceptance plan combines the right evidence for each requirement.
For incoming mold inspection or mold transfer, inspect the actual condition and documentation, not only a sample part. For PPAP, connect the inspection report to the production process, drawing revision and submission package.
Build the metrology record.
Keep the drawing, program, fixture, sample ID and report together so the result can be reproduced.
Open FAI guideQuestions buyers ask before approving this scope.
Can a CMM inspect every molded feature?
Should molded parts be measured free or restrained?
What should a CMM report include?
Does a CMM report prove the mold is good?
Need a project-specific answer?
Send the part, material, volume and stage. We will identify what can be confirmed before quotation or tooling.
Send the projectContinue the engineering review.
Keep the scope comparable.
The linked guides are written to support a project-specific supplier and tooling review.
PROJECT INTAKE / METROLOGY REVIEW
Define the characteristic before measuring it.
Send the drawing, critical features and inspection requirement. We can help align the report with the engineering decision.
Tell us where the project is now.
Send the files and context you have. Missing information can be confirmed during review.
Business inquiries only. For large files, include a secure Google Drive, Dropbox, OneDrive or WeTransfer link, or email tonney@a-mold.com after submitting.