MATERIALS / POM ACETAL

POM molding is a balance of low friction and tight process control.

POM acetal is selected for low friction, wear, stiffness and dimensional stability in gears, clips, fluid components and mechanical assemblies. It can also be sensitive to thermal history, gate design, shrinkage and post-molding dimensional change.

ABERY engineering note
Updated November 20, 2026

Do not apply a generic POM temperature profile. The grade, stabilizer, fillers and supplier recommendation matter, and the process record should include residence time and shutdown practice.

QUICK ANSWER

Review the exact POM grade, part thickness, gate and runner design, cooling, packing, shrinkage and dimensional requirement. Control drying only as specified by the supplier, avoid excessive heat history and validate the part after the specified stabilization period.

1. Define the mechanical function first.

POM may be used for gears, bearings, clips, latches, fluid-handling parts and other mechanical components. The application determines whether copolymer, homopolymer, impact-modified, glass-filled or lubricated grades should be considered.

Confirm load, speed, chemical contact, temperature and dimensional fit. A low-friction material does not remove the need to review tooth geometry, clearance, wear and assembly load.

MechanicalLoad, speed, impact, creep and fatigue.
WearSliding contact, lubricant and surface finish.
ChemicalFuel, water, cleaning and compatibility.
ThermalContinuous and peak temperature.
DimensionalFit, clearance and post-mold change.
ProcessGrade, drying and thermal history.

2. Design the runner and gate for clean processing.

POM can be sensitive to stagnant material and excessive heat history. Runner and gate design should avoid dead spots, abrupt shear and unnecessarily long residence time. Hot-runner use should be reviewed carefully with the material supplier.

Gate location affects packing, weld-line position and dimensional stability. For gears or precision features, the gate and ejection plan should be reviewed with the measurement and assembly condition.

  • Gate type and location.
  • Runner balance and dead spots.
  • Shear and gate freeze.
  • Vent location and cleaning.
  • Hot-runner suitability.
  • Gate removal and cosmetic effect.

3. Control shrinkage through cooling and packing.

POM shrinkage can change with wall thickness, mold temperature, packing, gate freeze and part geometry. A nominal shrinkage value from a data sheet is not enough for a precision feature.

Cooling should be uniform around ribs, bosses and thick sections. A packing profile that looks good on one cavity may create stress or dimensional movement in another. Record the process window and check the part after the required stabilization period.

WallNominal and local thickness.
CoolingMold temperature and circuit balance.
PackingGate freeze and hold profile.
EjectionPin layout and distortion.
StabilizationTime and condition before measurement.
InspectionDatum, fixture and critical features.

4. Avoid heat-history defects.

Long residence time, high melt temperature or poor purge can create degradation, odor, black specks or surface defects. The correct response is not simply to lower the temperature until the part stops filling.

Review barrel capacity, shot size, residence time, shutdown procedure and hot-runner volume. Record the purge and startup sequence so the production team can repeat it.

  • Barrel and hot-runner residence time.
  • Melt profile and actual readings.
  • Purge and shutdown procedure.
  • Screw speed and back pressure.
  • Venting and gas release.
  • Defect photos and material lot.

5. Validate the part after stabilization.

Measure dimensions in the specified condition and after the agreed settling time. For a precision mechanical part, include the functional or assembly check that matters to the customer.

Production release should tie the approved sample to the process window, material grade, inspection method and tool condition. If the gate, cooling, resin or machine changes, review whether a new qualification is needed.

  • Approved sample and drawing.
  • Material lot and drying record.
  • Process window and residence time.
  • Dimensional result after stabilization.
  • Functional or wear-related check.
  • Change and revalidation trigger.

Questions buyers ask before approving this scope.

What is POM used for in injection molding?
POM is commonly selected for mechanical and fluid-handling parts such as gears, clips, latches, bearings and housings. The exact grade must match load, wear, chemical and temperature requirements.
Is POM difficult to mold?
It can be processed successfully when the grade, residence time, temperature, venting and shutdown practice are controlled. Poor thermal history can create defects and dimensional variation.
Does POM need drying?
Follow the exact material supplier recommendation. POM grades differ, and over-drying or incorrect handling is not automatically beneficial.
How should POM dimensions be approved?
Use the drawing datum, defined fixture and the agreed stabilization time. Include a functional check when fit or mechanical performance is critical.

Need a project-specific answer?

Send the part, material, volume and stage. We will identify what can be confirmed before quotation or tooling.

Send the project

Keep the scope comparable.

The linked guides are written to support a project-specific supplier and tooling review.

PROJECT INTAKE / POM

Send the mechanical function and precision requirement.

We will review the resin grade, gate, cooling, stabilization and inspection questions before quotation.

Exact POM gradePart functionCritical dimensionsAnnual volumeAssembly conditionInspection method

Tell us where the project is now.

Send the files and context you have. Missing information can be confirmed during review.

A-MOLD Project Inquiry

Business inquiries only. For large files, include a secure Google Drive, Dropbox, OneDrive or WeTransfer link, or email tonney@a-mold.com after submitting.