TRANSFER / QUALIFICATION PROTOCOL

Qualification proves the mold can produce the approved part on the new press.

A transferred mold may arrive in good condition and still fail to produce an acceptable part. Machine fit, utilities, process window, measurement method and local material can all change the production result. Qualification is the evidence that the new combination is approved.

ABERY engineering note
Updated November 20, 2026

Receiving inspection and qualification are different gates. A clean, complete mold is not yet a released production process.

QUICK ANSWER

Complete the ownership and document review, inspect the mold as received, confirm machine and utility fit, establish a provisional process, run a defined sample plan, inspect critical dimensions and appearance, then compare the result with the approved part and issue a release or open-item status.

1. Start from the approved part and process record.

Qualification should use the approved drawing, material, appearance boundary and last known process as the reference. If the previous process is incomplete, say so before the trial.

A sample that looks like the old part is not enough. The qualification record must connect the part to the drawing, material lot, cavity, process and measurement method.

DrawingApproved revision and critical characteristics.
MaterialExact grade, color and approved source.
ProcessLast known window and machine condition.
SamplesRecent good and bad parts.
InspectionDatum, fixture and report format.
ApprovalCustomer and internal sign-off.

2. Verify the physical machine fit.

Check mold size, weight, locating ring, nozzle, ejector pattern, stroke, tie bars, platen mounting and handling. A tool that ran in the previous plant may need an adapter or a different machine.

Confirm water, air, electrical, hot-runner and sensor requirements. Record the as-installed condition before the trial so any later change is visible.

  • Mold height, width and weight.
  • Locating ring and nozzle.
  • Ejection and stroke.
  • Tie bars and platen.
  • Water and hot-runner utilities.
  • Safety and handling.

3. Establish a provisional process window.

Use the previous process as a starting point only if the machine, material and tool condition are comparable. Otherwise establish a provisional window from the material recommendation and actual fill behavior.

Record the setpoints, actual readings, cushion, shot size and any changes made during the trial. The window should be stable enough to support the sample plan.

  • Fill speed and pressure.
  • Packing and gate freeze.
  • Mold temperature and cooling.
  • Cycle and cushion.
  • Material drying and lot.
  • Process changes during trial.

4. Run the qualification sample plan.

Identify cavities, sample times and test methods. Inspect critical dimensions, appearance, function and any customer-specific requirement. For a multi-cavity mold, report the distribution rather than only one sample.

Compare the result with the approved boundary and previous data. If a dimension or appearance difference is found, determine whether it comes from the mold condition, machine, material, process or measurement.

  • Cavity and sample identification.
  • Dimensional and appearance result.
  • Functional or assembly check.
  • Process stability.
  • Deviation from old approval.
  • Corrective action and owner.

5. Issue a release status.

The result should be accepted, accepted with open items or rejected pending correction. Each open item needs evidence, an owner and a production impact.

Update the drawings, process sheet, maintenance plan and spare-parts list after qualification. If the machine, material, tool or process changes later, review whether the qualification remains valid.

  • Qualification report and samples.
  • Approved process window.
  • Inspection plan and records.
  • Open-item disposition.
  • Maintenance and spares.
  • Requalification triggers.

Questions buyers ask before approving this scope.

What is mold transfer qualification?
It is the process of proving that a transferred mold can produce the approved part on the new machine, material and process. It includes inspection, trial and documented approval.
Is incoming inspection the same as qualification?
No. Incoming inspection verifies condition and completeness. Qualification proves the production combination can meet the part requirement.
How many samples are needed?
It depends on the part, customer requirement and mold cavitation. The plan should cover all cavities, critical features and a representative run.
What can invalidate a qualification?
A machine, material, tool, process, inspection method or production location change may require review. The change-control rule should state when requalification is needed.

Need a project-specific answer?

Send the part, material, volume and stage. We will identify what can be confirmed before quotation or tooling.

Send the project

Keep the scope comparable.

The linked guides are written to support a project-specific supplier and tooling review.

PROJECT INTAKE / TRANSFER QUALIFICATION

Define the old and new production condition.

Send the mold history, approved samples, target machine and quality requirement. We will structure the qualification evidence.

Mold historyApproved sampleDrawing revisionTarget machineProcess sheetQuality requirement

Tell us where the project is now.

Send the files and context you have. Missing information can be confirmed during review.

A-MOLD Project Inquiry

Business inquiries only. For large files, include a secure Google Drive, Dropbox, OneDrive or WeTransfer link, or email tonney@a-mold.com after submitting.