PART DESIGN / LIVING HINGES
A living hinge needs material, flow and geometry to work together.
A living hinge is a thin section that flexes repeatedly. It can simplify a molded assembly, but it depends on the right material, hinge geometry, flow orientation, gate location, cooling and validation. A hinge that opens once may fail after repeated use.
ABERY engineering note
Updated November 20, 2026
Not every resin is suitable for a living hinge. The exact grade and supplier recommendation should be confirmed before the part design is fixed.
QUICK ANSWER
Define the material, hinge thickness, length, opening cycles, load and service temperature. Review the flow direction across the hinge, gate location, cooling, shutoff and ejection. Mold samples with the production process and test repeated opening, cracking and retention before approval.
1. Confirm the material and cycle requirement.
Living hinges are commonly considered in polypropylene and selected other resins. The exact grade, additive package and application determine whether the material is suitable.
State the number of open-close cycles, opening angle, load, temperature and chemical exposure. A one-time assembly hinge and a repeatedly used lid are different requirements.
| Material | Exact grade, additive and supplier data. |
|---|---|
| Geometry | Hinge thickness and length. |
| Motion | Opening angle and load. |
| Cycles | Expected flex life. |
| Environment | Temperature and chemical. |
| Assembly | Mating parts and closure. |
2. Orient the flow across the hinge.
The polymer orientation at the hinge can affect flex life. Gate location and flow direction should be designed so the hinge receives the intended molecular orientation.
A gate that leaves a weld line or stagnant flow at the hinge creates a weak point. Review the fill pattern and venting before the tool is cut.
- Gate and flow direction.
- Hinge thickness transition.
- Weld-line location.
- Fill and packing at the hinge.
- Cooling rate.
- Ejection contact.
3. Control thickness and transition.
The hinge needs a controlled thin section with a gradual transition into the thicker body. A sharp step can create stress and cracking.
The design should be reviewed with the material supplier or a proven reference. Copying a hinge geometry from a different resin is not a reliable design method.
| Hinge thickness | Flex and strength balance. |
|---|---|
| Land length | Bending zone and transition. |
| Radius | Stress concentration. |
| Body transition | Flow and cooling. |
| Draft | Release and surface. |
| Gate | Orientation and weld. |
4. Validate repeated flex.
Test the hinge through the required opening cycles and opening angle. Inspect for whitening, cracking, permanent set and retention loss.
Use production samples from the intended material, gate and process. A hand-trimmed sample or a different resin may not represent the hinge behavior.
- Open-close cycle count.
- Crack and whitening.
- Permanent set.
- Closure retention.
- Load and angle.
- Temperature or aging condition.
5. Define the production controls.
Record the approved material, gate, hinge geometry, process window and assembly cycle. A change in resin, color, gate, cooling or wall can change the hinge result.
Packaging and handling should avoid pre-flexing or damaging the hinge before assembly.
- Approved material and color.
- Gate and flow orientation.
- Process window.
- Flex-test result.
- Handling and packaging.
- Change and revalidation trigger.
Questions buyers ask before approving this scope.
Which plastic is best for a living hinge?
Does gate location matter for a living hinge?
How many cycles should a living hinge survive?
Can a living hinge be repaired if it cracks?
Need a project-specific answer?
Send the part, material, volume and stage. We will identify what can be confirmed before quotation or tooling.
Send the projectContinue the engineering review.
Keep the scope comparable.
The linked guides are written to support a project-specific supplier and tooling review.
PROJECT INTAKE / LIVING HINGE
Send the motion and material requirement.
We will review hinge geometry, flow orientation, tooling and flex validation before the design is frozen.
Tell us where the project is now.
Send the files and context you have. Missing information can be confirmed during review.
Business inquiries only. For large files, include a secure Google Drive, Dropbox, OneDrive or WeTransfer link, or email tonney@a-mold.com after submitting.