PROCESS CONTROL / WINDOW

A process window is a validated range, not a list of favorite settings.

A single shot can look good while sitting on the edge of a narrow or unstable process. A process window defines the range of settings that still produce an acceptable part under a defined material, tool and machine condition.

ABERY engineering note
Updated November 20, 2026

The window must be connected to the drawing, appearance standard and inspection method. A part is not “in window” if nobody defined what acceptable means.

QUICK ANSWER

Define the critical part characteristics, starting settings and allowed variation. Run a structured study across fill, packing, cooling and temperature boundaries, inspect the parts, document the stable range and set alarms or reaction limits. Then confirm the window across cavities and a production-length run.

1. Define what the window must protect.

The process window should be built around the part requirements: dimensions, appearance, weight, strength, seal or function. A window that only protects short shots is incomplete.

Identify the critical features and the defects that would stop production. Include the measurement method and the sample condition before testing the settings.

DimensionCritical features and datum.
AppearanceColor, flow, weld line and gate.
WeightFill and packing consistency.
FunctionAssembly, seal or strength.
ToolFlash, wear and ejection.
DocumentationMethod and sample condition.

2. Start from a stable baseline.

Establish a baseline using the material recommendation, tool design and machine capability. Confirm drying, shot size, cushion, fill pattern and ejection before the study.

A baseline that already needs excessive pressure or a temporary repair is not a reliable starting point. Correct known tool or material issues first.

  • Material grade, lot and drying.
  • Mold temperature and water flow.
  • Shot size and cushion.
  • Fill time and pressure.
  • Packing and gate freeze.
  • Ejection and part handling.

3. Study one factor at a time and then interactions.

Change fill, packing, cooling and temperature within defined ranges. Record the actual values and inspect the resulting parts. A design-of-experiments approach may be useful when several factors interact.

The goal is not to find the widest possible range at any quality level. It is to find a range that meets the requirement with enough margin to survive normal material, machine and environment variation.

FillSpeed and pressure-transfer boundary.
PackPressure and hold-time boundary.
CoolTime and mold-temperature boundary.
MeltTemperature and residence time.
MaterialLot and regrind variation.
MachineRepeatability and response.

4. Verify across cavities and time.

A window established on one cavity may not cover the whole tool. Measure all cavities and compare the distribution, not only the average.

Run enough cycles to include startup, steady state and a representative production period. Check whether dimensions or appearance drift as the mold temperature stabilizes.

  • All cavity samples.
  • Startup and steady-state parts.
  • Short and long run.
  • Part weight and dimensions.
  • Appearance and flash.
  • Process alarms and reaction plan.

5. Release and control the window.

Record the approved settings, actual readings, allowed ranges, sample identification and inspection plan. Define which changes require engineering approval.

A process window is invalidated by a material, tool, machine, drying, inspection or significant environmental change. Review the effect before returning the job to production.

  • Approved setpoints and ranges.
  • Actual machine readings.
  • Sample and inspection records.
  • Change-control rules.
  • Revalidation trigger.
  • Training and access control.

Questions buyers ask before approving this scope.

What is an injection molding process window?
It is the validated range of process conditions that produces an acceptable part under a defined material, tool, machine and inspection condition.
Is a process window the same as a process sheet?
A process sheet records the approved settings. The window also defines the allowed range and evidence that the part remains acceptable across that range.
How many samples are needed?
It depends on the part and risk. The study should cover the relevant settings, cavities, startup and steady-state conditions and the agreed critical characteristics.
When must the window be revalidated?
After a material, tool, machine, drying, inspection or major environmental change. The buyer and supplier should define the trigger in advance.

Need a project-specific answer?

Send the part, material, volume and stage. We will identify what can be confirmed before quotation or tooling.

Send the project

Keep the scope comparable.

The linked guides are written to support a project-specific supplier and tooling review.

PROJECT INTAKE / PROCESS WINDOW

Define the evidence behind the settings.

Send the part, resin, tool and critical quality requirements. We will structure the window and validation questions.

Part drawingExact resinTool dataCritical featuresInspection methodProduction volume

Tell us where the project is now.

Send the files and context you have. Missing information can be confirmed during review.

A-MOLD Project Inquiry

Business inquiries only. For large files, include a secure Google Drive, Dropbox, OneDrive or WeTransfer link, or email tonney@a-mold.com after submitting.