MATERIAL GUIDE / POLYCARBONATE
Polycarbonate molding starts with drying, stress and surface control.
Polycarbonate can deliver toughness, clarity and dimensional stability, but it is sensitive to moisture, high melt temperature, residence time and stress. Transparent or high-gloss parts expose tooling and process problems that a dark textured part may hide.
ABERY engineering note
Updated November 20, 2026
The exact PC grade matters. Optical, flame-retardant, impact-modified and PC/ABS grades do not share the same process window or surface expectation.
QUICK ANSWER
Confirm the exact PC grade and drying target, review gate location and stress, use a steel and polish strategy appropriate to the surface, and validate dimensions and appearance after an agreed settling condition.
1. Dry the resin and control the heat history.
Polycarbonate absorbs moisture and can hydrolyze when processed wet. Follow the resin supplier’s drying and residence-time requirements and verify the dryer condition rather than assuming that a setpoint is enough.
High melt temperature, long residence time or excessive shear can create yellowing, silver streaks, stress or reduced properties. The process record should include actual temperatures, recovery time and downtime handling.
- Exact PC or PC/ABS grade.
- Drying equipment and verified moisture condition.
- Melt temperature and residence time.
- Regrind policy and contamination control.
- Start-up, shutdown and purge procedure.
- Color and appearance standard.
2. Design the gate, cooling and ejection.
Gate location affects flow orientation, weld-line appearance and stress around the gate. For transparent parts, the gate and polishing plan should be reviewed before steel is cut.
Uneven cooling or aggressive ejection can lock stress into the part. A stress-sensitive part may pass a visual check and still crack during assembly or after aging.
| Gate | Check gate type, location, vestige and cosmetic requirement. |
|---|---|
| Steel | Review polishability, cleanliness and corrosion protection. |
| Cooling | Balance mold temperature and avoid local hot spots. |
| Packing | Control pressure transfer without overpacking. |
| Ejection | Check draft, pin location and release force. |
| Measurement | Agree settling time and inspection lighting. |
Specify the optical boundary.
Transparent does not mean “no visible defects.” Define the viewing area, lighting and acceptable gate or flow evidence.
Review mold design3. Validate appearance and stress.
Use an approved lighting condition and sample boundary. Review gate blush, flow marks, silver streaks, bubbles, black specks, scratches and stress patterns where they affect the application.
If the part will be coated, printed, assembled or exposed to chemicals, include that condition in the validation. A part that looks acceptable immediately after molding may fail later.
- T1 appearance under agreed lighting.
- Gate and flow-mark review.
- Dimensional layout after settling.
- Assembly or snap-fit trial.
- Coating, printing or cleaning compatibility if applicable.
- Stress-crack or impact requirement where specified.
4. RFQ inputs for PC parts.
Send the exact grade, transparency or color target, viewing area, surface finish, gate preference, critical dimensions, volume and any secondary operation. State whether the part is optical, structural, cosmetic or a combination.
Ask the supplier to identify the steel, polishing, drying, gate and inspection assumptions behind the quotation.
Do not compare PC by color alone.
Two visually similar parts can have different stress and long-term performance.
Open RFQ checklistQuestions buyers ask before approving this scope.
Why does polycarbonate turn yellow or show silver streaks?
Can PC be molded in a standard P20 mold?
How should transparent PC defects be judged?
Does PC need annealing?
Need a project-specific answer?
Send the part, material, volume and stage. We will identify what can be confirmed before quotation or tooling.
Send the projectContinue the engineering review.
Keep the scope comparable.
The linked guides are written to support a project-specific supplier and tooling review.
PROJECT INTAKE / POLYCARBONATE
Review the tool before chasing optical defects.
Send the PC grade, part geometry, optical boundary and volume. We can identify the gate, polish and validation questions for the project.
Tell us where the project is now.
Send the files and context you have. Missing information can be confirmed during review.
Business inquiries only. For large files, include a secure Google Drive, Dropbox, OneDrive or WeTransfer link, or email tonney@a-mold.com after submitting.