TROUBLESHOOTING / SPLAY & SILVER STREAKS
Splay and silver streaks start with the gas source.
Splay usually appears as dark, brown or silver deposits near the gate or in flow-front areas. Silver streaks are surface lines or bubbles caused by gas, moisture or volatiles. They may look similar, but the evidence needed to correct each one is different.
ABERY engineering note
Updated November 20, 2026
Do not purge the machine and change five temperatures at once. First identify whether the marks follow a material lot, cavity, hot-runner zone, drying condition or process change.
QUICK ANSWER
Dry the resin to its exact grade requirement, verify the dryer and moisture result, inspect purge and thermal history, confirm gate shear and venting, then isolate the affected cavity or hot-runner zone. Correct the confirmed gas source and recheck appearance, dimensions and process stability.
1. Separate the visual condition from the likely source.
Splay is often associated with volatile release, moisture, contamination or thermal degradation. It can leave a dark or silver trailing mark. Silver streaks can also come from gas trapped at the flow front, excessive shear, insufficient venting or a cold slug. The names are sometimes used loosely, so begin with the appearance pattern and sample location rather than the label.
Look at the first shot after startup, the first shot after a color change and samples from each cavity. If the defect appears only near one gate or one hot-runner tip, the tool or heat history is more likely than a general resin problem. If it appears across cavities after a lot change, inspect material and drying first.
| Near the gate | Check shear, gate freeze, hot-runner tip temperature and decomposition. |
|---|---|
| Along the flow front | Check venting, gas entrapment, fill speed and flow-front temperature. |
| Across all cavities | Check resin lot, drying, contamination and purge history. |
| At one cavity | Check nozzle, runner balance, vent and local tool condition. |
| After downtime | Check cold slugs, degraded material and startup purge. |
| After color change | Check cleaning, carrier compatibility and residual purge. |
2. Verify drying and material history.
Hygroscopic resins can retain moisture even when the hopper looks dry. Confirm the grade-specific drying temperature, dew point, residence time and airflow, then measure moisture with a method appropriate to the material. A dryer display is not a substitute for checking the actual condition of the resin.
Review the material certificate, lot change, regrind ratio, color masterbatch and any previous polymer in the machine. A small amount of incompatible purge can create surface defects that look like moisture splay.
- Record the exact resin grade and lot.
- Confirm dryer setpoint, dew point and residence time.
- Measure moisture before molding when the material is moisture-sensitive.
- Check regrind ratio, contamination and storage condition.
- Review masterbatch carrier and compatibility.
- Inspect purge and barrel history after a color or material change.
3. Review heat history, shear and venting.
Excessive barrel temperature, long residence time, restricted hot-runner passages and high shear at the gate can generate volatiles or char. The correct answer is not always a lower temperature; the melt must still fill and pack the part. Compare the recommended melt range with the actual profile and the pressure demand.
Vents must release air and gas before the flow front closes the cavity. Review vent location, depth, land length and cleanliness. For deep ribs, bosses and last-fill areas, confirm that air can escape rather than being compressed into the surface.
Look for a repeatable pattern.
Photograph the defect before purging or adjusting the process, and record cavity, shot number, material lot and process settings.
Compare color-streak causes4. Control the correction and restart.
Change one likely cause at a time. If drying is the suspected source, prove it with a measured moisture check and a controlled trial. If heat history is suspected, record the old and new profiles and inspect the first parts after the change. If venting is suspected, verify the tool condition before returning to production.
A short cosmetic improvement is not enough if the process has moved outside the approved window. Record the correction and check appearance across cavities, the full shot, the startup sequence and a longer run.
- Record the baseline defect and process settings.
- Use a measured material or tool check rather than a visual guess.
- Change one dominant variable at a time.
- Inspect first, middle and last parts from the run.
- Confirm the approved process window after correction.
- Add the check to startup and maintenance records.
5. Send the right evidence for a focused review.
Send photos with scale, the affected cavity and the shot sequence. Include material grade, lot, drying record, moisture result, melt and mold temperatures, fill time, packing profile, gate and runner details, vent layout and any recent tool or machine maintenance.
If the problem started after a mold transfer or repair, include the incoming condition, last approved process sheet and the first good sample. This lets the reviewer distinguish a material problem from a changed tool or machine condition.
Define the good sample.
Use a signed sample or approved photo standard; a verbal “no streaks” requirement is difficult to verify.
Use an FAI recordQuestions buyers ask before approving this scope.
What is the difference between splay and silver streaks?
Is moisture always the cause?
Can I fix it by increasing back pressure?
What sample information should I send?
Need a project-specific answer?
Send the part, material, volume and stage. We will identify what can be confirmed before quotation or tooling.
Send the projectContinue the engineering review.
Keep the scope comparable.
The linked guides are written to support a project-specific supplier and tooling review.
PROJECT INTAKE / DEFECT REVIEW
Show us the defect pattern and the process history.
Send the part photos, material data and process record. We will identify the evidence needed to separate moisture, gas, shear and tool causes.
Tell us where the project is now.
Send the files and context you have. Missing information can be confirmed during review.
Business inquiries only. For large files, include a secure Google Drive, Dropbox, OneDrive or WeTransfer link, or email tonney@a-mold.com after submitting.