MATERIALS / DRYING CONTROL
Drying is a measured material condition, not a hopper setting.
Moisture can create splay, silver streaks, bubbles, hydrolytic degradation and property loss in sensitive resins. A dryer display alone does not prove the resin is dry; the material, dryer, dew point, airflow, residence time and storage condition all matter.
ABERY engineering note
Updated November 20, 2026
Use the exact resin supplier recommendation. Drying temperatures, dew point and time are material-specific and can be harmful if copied from another grade.
QUICK ANSWER
Identify whether the resin is moisture-sensitive, confirm the required dryer type and dew-point target, verify airflow and residence time, measure moisture with an appropriate method and protect the dried material from reabsorption. Record the lot and drying history with the process and T1 samples.
1. Determine the material requirement.
Polycarbonate, PA, PBT, PET, PMMA and some TPU grades can be moisture-sensitive, while other materials may require little or no drying. The exact grade and supplier recommendation control the requirement.
Do not apply a generic temperature because another resin in the family uses it. Over-drying can also change color, additives or processing behavior.
| Polymer | Exact grade and supplier recommendation. |
|---|---|
| Initial moisture | Lot condition and storage. |
| Dryer | Desiccant, hot air or vacuum. |
| Dew point | Target and measurement method. |
| Time | Residence time at temperature. |
| Handling | Sealed or protected transfer. |
2. Verify the dryer condition.
A dryer can display the setpoint while the actual dew point, airflow or temperature is out of condition. Confirm the sensor, airflow path, desiccant condition and hopper distribution.
The material should experience the required condition for the required time. A small hopper with a short residence time may not dry a difficult resin even when the setpoint looks correct.
- Dryer type and capacity.
- Actual dew point.
- Inlet and return temperature.
- Airflow through the bed.
- Desiccant condition.
- Residence time and fill level.
3. Measure moisture and protect the dried resin.
Use a moisture measurement method appropriate to the resin and the decision. A visual check or a dryer display is not a moisture result.
Dried resin can reabsorb moisture during transfer, storage or a long production stop. Use sealed containers, dry conveying and a defined exposure limit.
| Measurement | Method and sample point. |
|---|---|
| Transfer | Closed or dry-air conveying. |
| Storage | Sealed and labeled container. |
| Exposure | Allowed time in the hopper. |
| Startup | Purge and first-part check. |
| Record | Lot, dryer and result. |
4. Connect drying to the defect and process record.
Splay, bubbles, silver streaks and property loss can indicate moisture, but similar defects can come from gas, contamination, shear or degradation. The drying record helps separate the source.
If a new material lot creates a defect, compare the drying record and moisture result before changing the entire process.
- Moisture result before molding.
- Dryer and hopper records.
- Material lot and color.
- Purge and startup.
- Part defect pattern.
- Process settings and samples.
5. Make drying a production control.
The approved production record should identify the dryer, target condition, verified readings and exposure limits. Operators need a reaction plan when a dryer alarm or material change occurs.
When the resin, dryer, residence time or storage condition changes, review whether the process and T1 evidence remain representative.
- Approved dryer settings.
- Dew-point verification.
- Moisture check frequency.
- Alarm and reaction plan.
- Material transfer control.
- Revalidation trigger.
Questions buyers ask before approving this scope.
Do all plastics need drying before injection molding?
Is a dryer display enough to prove the resin is dry?
Can over-drying damage resin?
What defects can moisture cause?
Need a project-specific answer?
Send the part, material, volume and stage. We will identify what can be confirmed before quotation or tooling.
Send the projectContinue the engineering review.
Keep the scope comparable.
The linked guides are written to support a project-specific supplier and tooling review.
PROJECT INTAKE / DRYING REVIEW
Send the resin and drying record.
We will link the material, dryer, moisture evidence and defect pattern before changing the process.
Tell us where the project is now.
Send the files and context you have. Missing information can be confirmed during review.
Business inquiries only. For large files, include a secure Google Drive, Dropbox, OneDrive or WeTransfer link, or email tonney@a-mold.com after submitting.