TROUBLESHOOTING / SHORT SHOTS
A short shot is a flow problem until the evidence says otherwise.
A short shot means the cavity did not fill before the material froze or the machine ran out of available flow. The cause can be material feed, shot size, pressure, gate freeze, venting, wall thickness, temperature or tool condition.
ABERY engineering note
Updated November 20, 2026
Do not simply raise pressure and temperature. First identify whether the cavity is starved, restricted or unable to release trapped air.
QUICK ANSWER
Record the short-shot pattern, affected cavities, material lot, drying, shot size, injection pressure, fill time, temperatures, gate and vent condition. Compare a short shot with a full shot and review the last-fill area. Correct the dominant restriction or gas source, then revalidate all cavities and the process window.
1. Map where the cavity stops filling.
A short shot pattern is evidence. If the part stops near the gate, the issue may be feed, pressure or gate freeze. If it stops at a thin section, the flow path may be too restrictive. If it stops at a boss or last-fill area, venting or air entrapment may be involved.
Photograph the short shot with cavity identification and compare it with a known good sample. Record the shot number and whether the condition changes after startup or during the run.
| Near gate | Feed, pressure, gate freeze or material supply. |
|---|---|
| Thin section | Flow restriction, speed or temperature. |
| Last-fill area | Venting, air trap or pressure loss. |
| One cavity | Runner balance, gate or vent issue. |
| All cavities | Material, shot size or machine condition. |
| After downtime | Cold material, purge or startup condition. |
2. Check the delivery system before changing the process.
Confirm the material is the correct grade, dry as required and feeding consistently. Check the hopper, screw recovery, shot size, cushion, nozzle, runner and gate for restrictions or contamination.
A machine may report pressure but still lack usable flow because the shot size, injection speed or pressure-transfer point is wrong. Review the actual stroke and cushion, not just the setpoint.
- Material grade, lot and feed.
- Shot size and cushion.
- Injection speed and pressure limit.
- Pressure-transfer position.
- Nozzle and runner condition.
- Gate freeze and venting.
3. Review the tool and flow path.
A short shot can expose a tool problem that a higher pressure would hide: a blocked gate, insufficient vent, cold slug, damaged runner or imbalanced multi-cavity feed.
Inspect the gate and runner for contamination or damage. Confirm vent depth and cleanliness. For a new tool, compare the short-shot pattern with the DFM expectation and ask whether the fill balance matches the design.
| Gate | Size, freeze and contamination. |
|---|---|
| Runner | Balance, obstruction and dead spots. |
| Vent | Location, depth and cleanliness. |
| Wall | Local thickness and flow length. |
| Cooling | Hot spot or premature freeze. |
| Tool | Insert, slide or ejector interference. |
4. Correct one dominant cause and recheck all cavities.
If the cause is material feed, correct drying or feed and verify with a controlled shot. If the cause is venting, clean or modify the vent and inspect the last-fill area. If the cause is a gate restriction, confirm the tool change before increasing pressure.
Record the old and new condition. A correction that only works on one cavity is not a production fix.
- Change one controlled variable.
- Keep the same material lot where possible.
- Inspect first, middle and last shots.
- Check all cavities.
- Record the new process window.
- Inspect for flash or overpacking after the change.
5. Decide whether the issue is process or design.
If the part only fills at an excessive pressure or temperature, the design or tool may be marginal. A process fix that consumes the entire machine capability can create stress, flash, wear and an unstable production window.
Escalate to DFM or mold review when wall, gate, runner, vent or machine fit is the limiting factor. Production release should include the approved fill pattern and the condition that would trigger a new trial.
- Pressure and temperature margin.
- Cushion and shot repeatability.
- Flash and part stress.
- Cavity balance and cycle.
- Process window width.
- Design or tool change trigger.
Questions buyers ask before approving this scope.
What causes short shots in injection molding?
Can I fix a short shot by increasing injection pressure?
Why does only one cavity short-shot?
What should be recorded for a short-shot review?
Need a project-specific answer?
Send the part, material, volume and stage. We will identify what can be confirmed before quotation or tooling.
Send the projectContinue the engineering review.
Keep the scope comparable.
The linked guides are written to support a project-specific supplier and tooling review.
PROJECT INTAKE / SHORT-SHOT REVIEW
Send the short-shot photo and process record.
We will help separate feed, pressure, gate, vent and design causes before the next process change.
Tell us where the project is now.
Send the files and context you have. Missing information can be confirmed during review.
Business inquiries only. For large files, include a secure Google Drive, Dropbox, OneDrive or WeTransfer link, or email tonney@a-mold.com after submitting.